Publikasi Scopus FKUI 2021 per tanggal 31 Agustus 2021 (582 artikel)

Rahyussalim A.J., Marsetio A.F., Kamal A.F., Supriadi S., Setyadi I., Pribadi P.M., Mubarok W., Kurniawati T.
55212166100;57192180884;56648996700;16040272500;57216397660;57194227346;57208440063;55213290600;
Synthesis, Structural Characterization, Degradation Rate, and Biocompatibility of Magnesium-Carbonate Apatite (Mg-Co3Ap) Composite and Its Potential as Biodegradable Orthopaedic Implant Base Material
2021
Journal of Nanomaterials
2021
6615614
Department of Orthopaedic and Traumatology, Faculty of Medicine Universitas Indonesia, Cipto Mangunkusumo National Central General Hospital, Jakarta, 10340, Indonesia; Department of Mechanical Engineering, Faculty of Engineering Universitas Indonesia, Jakarta, Depok, West Java, 16424, Indonesia; Division of Chemical Engineering, Department of Materials Engineering Science, Graduate School of Engineering Science, Osaka University, Toyonaka, Osaka, 560-8531, Japan; Stem Cells and Tissues Engineering Research Cluster, Indonesian Medical Education and Research Institute-Faculty of Medicine, Universitas Indonesia, Jakarta, 10340, Indonesia
Rahyussalim, A.J., Department of Orthopaedic and Traumatology, Faculty of Medicine Universitas Indonesia, Cipto Mangunkusumo National Central General Hospital, Jakarta, 10340, Indonesia; Marsetio, A.F., Department of Orthopaedic and Traumatology, Faculty of Medicine Universitas Indonesia, Cipto Mangunkusumo National Central General Hospital, Jakarta, 10340, Indonesia; Kamal, A.F., Department of Orthopaedic and Traumatology, Faculty of Medicine Universitas Indonesia, Cipto Mangunkusumo National Central General Hospital, Jakarta, 10340, Indonesia; Supriadi, S., Department of Mechanical Engineering, Faculty of Engineering Universitas Indonesia, Jakarta, Depok, West Java, 16424, Indonesia; Setyadi, I., Department of Mechanical Engineering, Faculty of Engineering Universitas Indonesia, Jakarta, Depok, West Java, 16424, Indonesia; Pribadi, P.M., Department of Mechanical Engineering, Faculty of Engineering Universitas Indonesia, Jakarta, Depok, West Java, 16424, Indonesia; Mubarok, W., Division of Chemical Engineering, Department of Materials Engineering Science, Graduate School of Engineering Science, Osaka University, Toyonaka, Osaka, 560-8531, Japan; Kurniawati, T., Stem Cells and Tissues Engineering Research Cluster, Indonesian Medical Education and Research Institute-Faculty of Medicine, Universitas Indonesia, Jakarta, 10340, Indonesia
Suitable biomechanical properties with a degradation rate parallel to normal bone healing time are vital characteristics for biodegradable implant material in orthopaedics. Magnesium (Mg) is a natural micronutrient as well as biodegradable metal with biomechanical characteristics close to that of the human bone, while carbonate apatite (CO3Ap) is a biological apatite with good osteoconductivity which allows bone healing without forming fibrotic tissue. We fabricated a Mg-CO3Ap composite with various content ratios by powder metallurgy, various milling times (3, 5, and 7 hours) at 200 RPM, warm compaction at 300°C and pressure of 265 MPa, sintering at 550°C, holding time of 1 hour, heating rate of 5°C/minutes, and room atmosphere cooling. Specimens were successfully created and had a density comparable to that of the human bone (1.95-2.13 g/cm3). Good biocompatibility was found on Mg-10% CO3Ap composite (66.67% of viable cells). Nevertheless, its biomechanical properties and corrosion resistance were inferior to the human bone. Additionally, the materials of the composites make the surrounding environment alkaline. Interparticle consolidation and grain size were dissatisfactory due to microstructural pores presumably formed by the Mg(OH)2 layer and oxidation process during sintering. However, alkaline condition caused by the material corrosion by-product might be beneficial for bone healing and wound healing process. Modifications on fabrication parameters are needed to improve interparticle consolidation, refine grain size, improve biomechanical strength, reduce corrosion products, and improve the degradation rate. © 2021 Ahmad Jabir Rahyussalim et al.
Apatite; Biocompatibility; Biomechanics; Composite structures; Corrosion resistance; Degradation; Grain size and shape; Orthopedics; Powder metallurgy; Sintering; Tissue regeneration; Biodegradable implants; Biomechanical characteristics; Biomechanical properties; Fabrication parameters; Magnesium carbonate apatites; Structural characterization; Surrounding environment; Wound healing process; Magnesium metallurgy
Hindawi Limited
16874110
Article
Q2
463
10759